rtl3070 - No Scan Results (ever)

Live forum: http://rt2x00.serialmonkey.com/viewtopic.php?t=5835

okias

16-11-2009 23:54:21

Kernel tested 2.6.31,2.6.32-rc7, dist Ubuntu, Gentoo
Device Air Live WN-360USB
RT3070 driver from website works...

dmesg (errors are here, because I few tried wifi without firmware)
[code11ddaqm0]rt2800usb 2-4:1.0: usb_probe_interface
rt2800usb 2-4:1.0: usb_probe_interface - got id
phy1 -> rt2x00_set_chip: Info - Chipset detected - rt: 1600, rf: 0005, rev: 30700200.
PM: Adding info for No Bus:phy1
PM: Adding info for No Bus:rfkill1
PM: Adding info for No Bus:wmaster1
phy1: Selected rate control algorithm 'minstrel'
PM: Adding info for No Bus:wlan1
PM: Adding info for No Bus:rt2800usb-phy1::radio
Registered led device: rt2800usb-phy1::radio
PM: Adding info for No Bus:rt2800usb-phy1::assoc
Registered led device: rt2800usb-phy1::assoc
PM: Adding info for No Bus:rt2800usb-phy1::quality
Registered led device: rt2800usb-phy1::quality
usbcore: registered new interface driver rt2800usb
phy1 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'.
rt2800usb 2-4:1.0: firmware: requesting rt2870.bin
PM: Adding info for No Bus:2-4:1.0
PM: Removing info for No Bus:2-4:1.0
phy1 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy1 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'.
rt2800usb 2-4:1.0: firmware: requesting rt2870.bin
PM: Adding info for No Bus:2-4:1.0
PM: Removing info for No Bus:2-4:1.0
phy1 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy1 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'.
rt2800usb 2-4:1.0: firmware: requesting rt2870.bin
PM: Adding info for No Bus:2-4:1.0
PM: Removing info for No Bus:2-4:1.0
phy1 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy1 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'.
rt2800usb 2-4:1.0: firmware: requesting rt2870.bin
PM: Adding info for No Bus:2-4:1.0
PM: Removing info for No Bus:2-4:1.0
phy1 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8.
phy1 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
phy1 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
phy1 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
phy1 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
ADDRCONF(NETDEV_UP): wlan1: link is not ready
[/code11ddaqm0]
lsusb
[code11ddaqm0]Bus 002 Device 005: ID 1b75:3072
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1b75
idProduct 0x3072
bcdDevice 1.01
iManufacturer 1 Ralink
iProduct 2 802.11 n WLAN
iSerial 3 1.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 450mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 7
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 5 1.0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
[/code11ddaqm0]

rgx112

11-12-2009 21:53:47

Hi.

i have the same problem.
my device is the same WN-360USB from AirLive
specifically
vendor 1b75 ("Ovislink Corp."), product 3072 ("AirLive WN-360USB adapter")
(found in http//cateee.net/lkddb/web-lkddb/RT2800USB.html)

lsusb
[code1yapesyx]1b75:3072[/code1yapesyx]

i compiled the last kernel 2.6.32 with rt2800 USB support but when scanning, the result is "[i1yapesyx]No Scan Results[/i1yapesyx]"

I also tried with ralinktech driver called RT3070USB(RT307x) from http//www.ralinktech.com/support.php?s=2 but this have not support for 1b75 vendor

mmm
i dont know what more to do

any suggestion is welcome
thanks
Marcos