Chipset RT2070L, USB id 148f:3070 - weird problems

Live forum: http://rt2x00.serialmonkey.com/viewtopic.php?t=6066

fisted

21-04-2010 05:56:39

Hello everyone,

i have problems getting my USB 802.11bg(n?) device to work. Its pretty weird.

First of all, some information on the mentioned device and the host environment
I am running an up-to-date gentoo linux, with (as of now) a vanilla kernel version 2.6.34-rc5 on my notebook.
I bought a cheap wireless USB device (no-name). There is no information on the manufacturer, the only thing printed on the enclosure is [b2w7w8qdk]802.11b/g 54Mbps Wireless USB Adapter.[/b2w7w8qdk]
its USB vendor and product ID are [b2w7w8qdk]148f3070[/b2w7w8qdk] which is the first weird thing, because other users seem to have devices supporting 802.11n, with the same product id.
in addition, dmesg is talking about 802.11n, too when plugging the device in, we get
[code2w7w8qdk]
[ 3238.774419] usb 1-1: New USB device found, idVendor=148f, idProduct=3070
[ 3238.774425] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3238.774431] usb 1-1: Product: [b]802.11 n WLAN[/b]
[/code2w7w8qdk]

odd.

i opened the dongle to see the chipset, and its a [b2w7w8qdk]RT2070L[/b2w7w8qdk] (there are no typos)

the overall result is, when plugging the device in, rt2800usb & co. get loaded, everything _seems_ be properly done. a network interface is created which i can bring up/down via ifconfig, but when looking for access points via [b2w7w8qdk]iwlist wlan[/b2w7w8qdk]N[b2w7w8qdk] scan[/b2w7w8qdk] i always get [b2w7w8qdk]"no scan results"[/b2w7w8qdk]

i tried several versions of rt2870.bin, which [b2w7w8qdk]seems[/b2w7w8qdk] to be the proper firmware file, but its always the same.

after hours of searching, i found a thread in which one had a similar device, and the people were talking about ht enabled where it should'nt be. i placed a printk into rt2800lib.c to see whether or not its enabled on my site, it was, so i manually disabled it like this
from
[code2w7w8qdk]if (!rt2x00_rf(rt2x00dev, RF2020))
spec->ht.ht_supported = true;
else
spec->ht.ht_supported = false;
[/code2w7w8qdk]
to
[code2w7w8qdk]
//if (!rt2x00_rf(rt2x00dev, RF2020))
// spec->ht.ht_supported = true;
//else
spec->ht.ht_supported = false;
[/code2w7w8qdk]

to see if it works, but it doesnt, again i get "no scan results" when trying to scan.

i dont know how to proceed, i dont really even understand the problem.

any suggestions? thanks in advance

please note that the staging (rt2870sta) drivers _do_ work, at least i can scan for AP's. but that driver does not work with kismet, this is the reason why i really need rt2x00 working, i cannot fall back to the staging driver

now following some information on my system, various outputs etc.

lsusb | grep Ralink
[code2w7w8qdk]
Bus 001 Device 002: ID 148f:3070 Ralink Technology, Corp.[/code2w7w8qdk]

ifconfig, while down
[code2w7w8qdk]wlan1 Link encap:Ethernet HWaddr 00:a1:b0:eb:62:58
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[/code2w7w8qdk]
ifconfig, while up
[code2w7w8qdk]wlan1 Link encap:Ethernet HWaddr 00:a1:b0:eb:62:58
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[/code2w7w8qdk]

iwconfig, while down
[code2w7w8qdk]wlan1 IEEE 802.11bgn Mode:Managed Access Point: Not-Associated
Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
[/code2w7w8qdk]
iwconfig, while up
[code2w7w8qdk]wlan1 IEEE 802.11bgn Mode:Managed Access Point: Not-Associated
Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
[/code2w7w8qdk]

iwlist wlan1 scan
[code2w7w8qdk]wlan1 No scan results
[/code2w7w8qdk]

lsmod (wireless stuff is the only thing i built as modules)
[code2w7w8qdk]Module Size Used by
rt2800usb 8167 0
rt2800lib 19492 1 rt2800usb
rt2x00usb 6411 2 rt2800usb,rt2800lib
rt2x00lib 21951 2 rt2800lib,rt2x00usb[/code2w7w8qdk]

uname -a
[code2w7w8qdk]
Linux fistbook 2.6.34-rc5l16 #1 SMP Tue Apr 20 23:22:13 CEST 2010 x86_64 AMD Athlon(tm) II Dual-Core M300 AuthenticAMD GNU/Linux[/code2w7w8qdk]

i made a clean reboot, device [b2w7w8qdk]un[/b2w7w8qdk]plugged, here is dmesg
(dont be confused because of the name wlan1, wlan0 is the internal wlan adapter which i disabled (blacklisted the module ath9k))
i removed a chunk of early (most probably irrelevant to my problem) dmesg lines, to not run into max chars limit
[code2w7w8qdk]
[ 0.000000] Linux version 2.6.34-rc5l16 (root@fistbook) (gcc version 4.4.3 (Gentoo 4.4.3 p1.0) ) #1 SMP Tue Apr 20 23:22:13 CEST 2010
[ 0.000000] Command line: root=/dev/sda5 ro
...
[ 0.192357] Bluetooth: Core ver 2.15
[ 0.192357] NET: Registered protocol family 31
[ 0.192357] Bluetooth: HCI device and connection manager initialized
[ 0.192357] Bluetooth: HCI socket layer initialized
[ 0.193077] cfg80211: Calling CRDA to update world regulatory domain
[ 0.193149] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.193305] hpet0: 4 comparators, 32-bit 14.318180 MHz counter
[ 0.194028] Switching to clocksource tsc
[ 0.196045] Slow work thread pool: Starting up
[ 0.196219] Slow work thread pool: Ready
[ 0.196349] FS-Cache: Loaded
[ 0.196475] pnp: PnP ACPI init
[ 0.196605] ACPI: bus type pnp registered
[ 0.200940] pnp: PnP ACPI: found 13 devices
[ 0.201106] ACPI: ACPI bus type pnp unregistered
[ 0.201243] system 00:07: [io 0x0250-0x0253] has been reserved
[ 0.201369] system 00:07: [io 0x0256-0x025f] has been reserved
[ 0.201496] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.201622] system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.201751] system 00:08: [io 0x04d0-0x04d1] has been reserved
[ 0.201853] system 00:08: [io 0x040b] has been reserved
[ 0.201981] system 00:08: [io 0x04d6] has been reserved
[ 0.202108] system 00:08: [io 0x0c00-0x0c01] has been reserved
[ 0.202235] system 00:08: [io 0x0c14] has been reserved
[ 0.202361] system 00:08: [io 0x0c50-0x0c51] has been reserved
[ 0.202489] system 00:08: [io 0x0c52] has been reserved
[ 0.202615] system 00:08: [io 0x0c6c] has been reserved
[ 0.202741] system 00:08: [io 0x0c6f] has been reserved
[ 0.202867] system 00:08: [io 0x0cd0-0x0cd1] has been reserved
[ 0.202994] system 00:08: [io 0x0cd2-0x0cd3] has been reserved
[ 0.203122] system 00:08: [io 0x0cd4-0x0cd5] has been reserved
[ 0.203249] system 00:08: [io 0x0cd6-0x0cd7] has been reserved
[ 0.203376] system 00:08: [io 0x0cd8-0x0cdf] has been reserved
[ 0.203503] system 00:08: [io 0x0800-0x089f] has been reserved
[ 0.203631] system 00:08: [io 0x0b00-0x0b0f] has been reserved
[ 0.203758] system 00:08: [io 0x0b20-0x0b3f] has been reserved
[ 0.203860] system 00:08: [io 0x0900-0x090f] has been reserved
[ 0.203987] system 00:08: [io 0x0910-0x091f] has been reserved
[ 0.204115] system 00:08: [io 0xfe00-0xfefe] has been reserved
[ 0.204243] system 00:08: [io 0x0f50] has been reserved
[ 0.204370] system 00:08: [mem 0xffb80000-0xffbfffff] has been reserved
[ 0.204497] system 00:08: [mem 0xfec10000-0xfec1001f] has been reserved
[ 0.204628] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.204756] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.204858] system 00:0c: [mem 0x000c0000-0x000cffff] has been reserved
[ 0.204985] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.205111] system 00:0c: [mem 0x00100000-0xcfffffff] could not be reserved
[ 0.205237] system 00:0c: [mem 0xe0000000-0xffffffff] could not be reserved
[ 0.210636] PCI: max bus depth: 1 pci_try_num: 2
[ 0.210656] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.210782] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.210918] pci 0000:00:01.0: bridge window [mem 0xfe800000-0xfe9fffff]
[ 0.211055] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.211238] pci 0000:00:05.0: PCI bridge to [bus 02-02]
[ 0.211364] pci 0000:00:05.0: bridge window [io 0xe000-0xefff]
[ 0.211490] pci 0000:00:05.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.211617] pci 0000:00:05.0: bridge window [mem pref disabled]
[ 0.211744] pci 0000:00:06.0: PCI bridge to [bus 03-03]
[ 0.211868] pci 0000:00:06.0: bridge window [io disabled]
[ 0.211994] pci 0000:00:06.0: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.212121] pci 0000:00:06.0: bridge window [mem pref disabled]
[ 0.212248] pci 0000:00:14.4: PCI bridge to [bus 04-04]
[ 0.212372] pci 0000:00:14.4: bridge window [io disabled]
[ 0.212500] pci 0000:00:14.4: bridge window [mem disabled]
[ 0.212627] pci 0000:00:14.4: bridge window [mem pref disabled]
[ 0.212769] pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.212913] pci 0000:00:05.0: setting latency timer to 64
[ 0.212920] pci 0000:00:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.213046] pci 0000:00:06.0: setting latency timer to 64
[ 0.213053] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.213055] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.213057] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.213060] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.213062] pci_bus 0000:00: resource 8 [mem 0xd0000000-0xdfffffff]
[ 0.213064] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfebfffff]
[ 0.213067] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 0.213069] pci_bus 0000:01: resource 1 [mem 0xfe800000-0xfe9fffff]
[ 0.213071] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.213074] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.213076] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.213078] pci_bus 0000:03: resource 1 [mem 0xfeb00000-0xfebfffff]
[ 0.213081] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
[ 0.213083] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
[ 0.213085] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.213088] pci_bus 0000:04: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.213090] pci_bus 0000:04: resource 8 [mem 0xd0000000-0xdfffffff]
[ 0.213092] pci_bus 0000:04: resource 9 [mem 0xf0000000-0xfebfffff]
[ 0.213112] NET: Registered protocol family 2
[ 0.213298] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.213834] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.215477] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.216015] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.216142] TCP reno registered
[ 0.216269] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.216421] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.216632] NET: Registered protocol family 1
[ 0.216971] RPC: Registered udp transport module.
[ 0.217066] RPC: Registered tcp transport module.
[ 0.217191] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.217325] pci 0000:00:01.0: MSI quirk detected; subordinate MSI disabled
[ 0.217538] pci 0000:01:05.0: Boot video device
[ 0.217548] PCI: CLS 64 bytes, default 64
[ 0.217676] Simple Boot Flag at 0x71 set to 0x1
[ 0.218695] microcode: CPU0: patch_level=0x1000098
[ 0.218830] microcode: CPU1: patch_level=0x1000098
[ 0.219028] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 0.219254] Scanning for low memory corruption every 60 seconds
[ 0.219552] Intel PCLMULQDQ-NI instructions are not detected.
[ 0.223429] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.223770] fuse init (API version 7.13)
[ 0.224255] msgmni has been set to 6532
[ 0.226495] alg: No test for stdrng (krng)
[ 0.231284] alg: No test for fips(ansi_cprng) (fips_ansi_cprng)
[ 0.231627] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.231777] io scheduler noop registered
[ 0.232042] io scheduler cfq registered (default)
[ 0.232301] pcieport 0000:00:05.0: setting latency timer to 64
[ 0.232327] pcieport 0000:00:05.0: irq 24 for MSI/MSI-X
[ 0.232449] pcieport 0000:00:06.0: setting latency timer to 64
[ 0.232469] pcieport 0000:00:06.0: irq 25 for MSI/MSI-X
[ 0.232636] pcieport 0000:00:05.0: Requesting control of PCIe PME from ACPI BIOS
[ 0.232791] pcieport 0000:00:05.0: Failed to receive control of PCIe PME service: no _OSC support
[ 0.232982] pcie_pme: probe of 0000:00:05.0:pcie01 failed with error -13
[ 0.233109] pcieport 0000:00:06.0: Requesting control of PCIe PME from ACPI BIOS
[ 0.233291] pcieport 0000:00:06.0: Failed to receive control of PCIe PME service: no _OSC support
[ 0.233473] pcie_pme: probe of 0000:00:06.0:pcie01 failed with error -13
[ 0.233686] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.233935] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.234353] power_supply AC0: uevent
[ 0.234355] power_supply AC0: No power supply yet
[ 0.234415] power_supply AC0: power_supply_changed
[ 0.234419] ACPI: AC Adapter [AC0] (on-line)
[ 0.234545] power_supply AC0: power_supply_changed_work
[ 0.234548] power_supply AC0: power_supply_update_gen_leds 1
[ 0.234552] power_supply AC0: uevent
[ 0.234554] power_supply AC0: POWER_SUPPLY_NAME=AC0
[ 0.234557] power_supply AC0: Static prop TYPE=Mains
[ 0.234560] power_supply AC0: 1 dynamic props
[ 0.234562] power_supply AC0: prop ONLINE=1
[ 0.234762] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.234928] ACPI: Power Button [PWRB]
[ 0.235117] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 0.235266] ACPI: Sleep Button [SLPB]
[ 0.235495] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[ 0.237458] ACPI: Lid Switch [LID]
[ 0.237777] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 0.237947] ACPI: Power Button [PWRF]
[ 0.242950] acpi device:05: registered as cooling_device0
[ 0.243297] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:01/LNXVIDEO:00/input/input4
[ 0.243448] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 0.243701] ACPI: processor limited to max C-state 1
[ 0.251961] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.252102] ACPI: Thermal Zone [THRM] (62 C)
[ 0.252887] i2c-core: driver [LP3971] registered
[ 0.256601] ipmi message handler version 39.2
[ 0.256737] ipmi device interface
[ 0.257101] IPMI System Interface driver.
[ 0.269983] ipmi_si: Unable to find any System Interface(s)
[ 0.270110] IPMI Watchdog: driver initialized
[ 0.270261] Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot.
[ 0.270584] [drm] Initialized drm 1.1.0 20060810
[ 0.270854] [drm] radeon defaulting to kernel modesetting.
[ 0.271004] [drm] radeon kernel modesetting enabled.
[ 0.271183] radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.271346] radeon 0000:01:05.0: setting latency timer to 64
[ 0.273242] [drm] initializing kernel modesetting (RS880 0x1002:0x9712).
[ 0.273468] [drm] register mmio base: 0xFE9F0000
[ 0.273596] [drm] register mmio size: 65536
[ 0.279135] ATOM BIOS: K51/71AE
[ 0.279237] [drm] Clocks initialized !
[ 0.279329] [drm] 1 Power State(s)
[ 0.279446] [drm] State 0 Default (default)
[ 0.279579] [drm] 1 Clock Mode(s)
[ 0.279695] [drm] 0 engine: 500000
[ 0.279858] [drm] radeon: power management initialized
[ 0.279983] radeon 0000:01:05.0: VRAM: 256M 0xC0000000 - 0xCFFFFFFF (256M used)
[ 0.280186] radeon 0000:01:05.0: GTT: 512M 0xA0000000 - 0xBFFFFFFF
[ 0.280448] [drm] Detected VRAM RAM=256M, BAR=256M
[ 0.280591] [drm] RAM width 32bits DDR
[ 0.280761] [TTM] Zone kernel: Available graphics memory: 1672234 kiB.
[ 0.280908] [drm] radeon: 256M of VRAM memory ready
[ 0.281030] [drm] radeon: 512M of GTT memory ready.
[ 0.281199] [drm] radeon: irq initialized.
[ 0.281328] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 0.282596] [drm] Loading RS780 Microcode
[ 0.282728] platform radeon_cp.0: firmware: using built-in firmware radeon/RS780_pfp.bin
[ 0.282942] platform radeon_cp.0: firmware: using built-in firmware radeon/RS780_me.bin
[ 0.283123] platform radeon_cp.0: firmware: using built-in firmware radeon/R600_rlc.bin
[ 0.283658] power_supply BAT0: uevent
[ 0.283661] power_supply BAT0: No power supply yet
[ 0.284932] power_supply BAT0: power_supply_changed
[ 0.285099] power_supply BAT0: power_supply_changed_work
[ 0.297950] ACPI: Battery Slot [BAT0] (battery present)
[ 0.307787] power_supply BAT0: power_supply_update_bat_leds 4
[ 0.307796] power_supply BAT0: uevent
[ 0.307798] power_supply BAT0: POWER_SUPPLY_NAME=BAT0
[ 0.307804] power_supply BAT0: Static prop TYPE=Battery
[ 0.307806] power_supply BAT0: 14 dynamic props
[ 0.307809] power_supply BAT0: prop STATUS=Full
[ 0.307812] power_supply BAT0: prop PRESENT=1
[ 0.307815] power_supply BAT0: prop TECHNOLOGY=Li-ion
[ 0.307817] power_supply BAT0: prop CYCLE_COUNT=0
[ 0.307820] power_supply BAT0: prop VOLTAGE_MIN_DESIGN=11100000
[ 0.307822] power_supply BAT0: prop VOLTAGE_NOW=12450000
[ 0.307825] power_supply BAT0: prop CURRENT_NOW=0
[ 0.307827] power_supply BAT0: prop POWER_NOW=0
[ 0.307829] power_supply BAT0: prop ENERGY_FULL_DESIGN=48400000
[ 0.307832] power_supply BAT0: prop ENERGY_FULL=44858000
[ 0.307845] power_supply BAT0: prop ENERGY_NOW=44858000
[ 0.307847] power_supply BAT0: prop MODEL_NAME=F82--22
[ 0.307850] power_supply BAT0: prop MANUFACTURER=ASUSTEK
[ 0.307852] power_supply BAT0: prop SERIAL_NUMBER=
[ 0.320309] [drm] ring test succeeded in 1 usecs
[ 0.320565] [drm] radeon: ib pool ready.
[ 0.320715] [drm] ib test succeeded in 0 usecs
[ 0.320842] [drm] Enabling audio support
[ 0.320900] [drm] Unknown TV standard; defaulting to NTSC
[ 0.321234] i2c i2c-0: adapter [Radeon i2c bit bus VGA] registered
[ 0.321339] i2c i2c-1: adapter [Radeon i2c bit bus LVDS] registered
[ 0.321434] i2c i2c-2: adapter [Radeon i2c bit bus HDMI] registered
[ 0.321497] [drm] Radeon Display Connectors
[ 0.321621] [drm] Connector 0:
[ 0.321745] [drm] VGA
[ 0.321841] [drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
[ 0.321987] [drm] Encoders:
[ 0.322111] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 0.322235] [drm] Connector 1:
[ 0.322358] [drm] LVDS
[ 0.322482] [drm] DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
[ 0.322661] [drm] Encoders:
[ 0.322784] [drm] LCD1: INTERNAL_KLDSCP_LVTMA
[ 0.322879] [drm] Connector 2:
[ 0.323002] [drm] HDMI-A
[ 0.323124] [drm] HPD1
[ 0.323248] [drm] DDC: 0x7e60 0x7e60 0x7e64 0x7e64 0x7e68 0x7e68 0x7e6c 0x7e6c
[ 0.323428] [drm] Encoders:
[ 0.323551] [drm] DFP1: INTERNAL_UNIPHY
[ 0.323676] i2c i2c-0: master_xfer[0] W, addr=0x50, len=1
[ 0.323679] i2c i2c-0: master_xfer[1] R, addr=0x50, len=128
[ 0.325555] i2c i2c-0: NAK from device addr 0x50 msg #0
[ 0.325614] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
[ 0.325616] i2c i2c-1: master_xfer[1] R, addr=0x50, len=128
[ 0.375500] i2c i2c-2: master_xfer[0] W, addr=0x50, len=1
[ 0.375502] i2c i2c-2: master_xfer[1] R, addr=0x50, len=128
[ 0.377377] i2c i2c-2: NAK from device addr 0x50 msg #0
[ 0.385086] i2c i2c-0: master_xfer[0] W, addr=0x50, len=1
[ 0.385088] i2c i2c-0: master_xfer[1] R, addr=0x50, len=1
[ 0.386964] i2c i2c-0: NAK from device addr 0x50 msg #0
[ 0.392202] i2c i2c-1: master_xfer[0] W, addr=0x50, len=1
[ 0.392205] i2c i2c-1: master_xfer[1] R, addr=0x50, len=128
[ 0.442118] i2c i2c-2: master_xfer[0] W, addr=0x50, len=1
[ 0.442120] i2c i2c-2: master_xfer[1] R, addr=0x50, len=1
[ 0.443995] i2c i2c-2: NAK from device addr 0x50 msg #0
[ 0.455400] [drm] fb mappable at 0xD0141000
[ 0.455560] [drm] vram apper at 0xD0000000
[ 0.455684] [drm] size 4325376
[ 0.455807] [drm] fb depth is 24
[ 0.455934] [drm] pitch is 5632
[ 1.391832] Console: switching to colour frame buffer device 170x48
[ 1.403234] fb0: radeondrmfb frame buffer device
[ 1.403235] registered panic notifier
[ 1.403389] [drm] Initialized radeon 2.3.0 20080528 for 0000:01:05.0 on minor 0
[ 1.403614] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.405768] brd: module loaded
[ 1.406582] loop: module loaded
[ 1.406942] nbd: registered device at major 43
[ 1.408691] i2c-core: driver [at24] registered
[ 1.408721] i2c-core: driver [eeprom] registered
[ 1.408750] i2c-core: driver [max6875] registered
[ 1.409098] ahci 0000:00:11.0: version 3.0
[ 1.409117] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1.409416] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3 impl SATA mode
[ 1.409552] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc
[ 1.409979] scsi0 : ahci
[ 1.410222] scsi1 : ahci
[ 1.410359] scsi2 : ahci
[ 1.410531] scsi3 : ahci
[ 1.410700] scsi4 : ahci
[ 1.410870] scsi5 : ahci
[ 1.411235] ata1: SATA max UDMA/133 abar m1024@0xfe7ffc00 port 0xfe7ffd00 irq 22
[ 1.411394] ata2: SATA max UDMA/133 abar m1024@0xfe7ffc00 port 0xfe7ffd80 irq 22
[ 1.411517] ata3: DUMMY
[ 1.411559] ata4: DUMMY
[ 1.411601] ata5: DUMMY
[ 1.411643] ata6: DUMMY
[ 1.411811] ATL1E 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.413627] ATL1E 0000:02:00.0: setting latency timer to 64
[ 1.425347] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.427168] ehci_hcd: block sizes: qh 104 qtd 96 itd 192 sitd 96
[ 1.427231] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.429189] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 1.431142] drivers/usb/core/inode.c: creating file 'devices'
[ 1.431145] drivers/usb/core/inode.c: creating file '001'
[ 1.431148] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 1.433225] ehci_hcd 0000:00:12.2: reset hcs_params 0x102306 dbg=1 cc=2 pcc=3 ordered !ppc ports=6
[ 1.433229] ehci_hcd 0000:00:12.2: reset hcc_params a072 thresh 7 uframes 256/512/1024
[ 1.433257] ehci_hcd 0000:00:12.2: debug port 1
[ 1.435311] ehci_hcd 0000:00:12.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.435322] ehci_hcd 0000:00:12.2: MWI active
[ 1.435324] ehci_hcd 0000:00:12.2: supports USB remote wakeup
[ 1.435338] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe7ff800
[ 1.437462] ehci_hcd 0000:00:12.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.437469] ehci_hcd 0000:00:12.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
[ 1.444086] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 1.446299] usb usb1: default language 0x0409
[ 1.446306] usb usb1: udev 1, busnum 1, minor = 0
[ 1.446308] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.448580] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.450923] usb usb1: Product: EHCI Host Controller
[ 1.453307] usb usb1: Manufacturer: Linux 2.6.34-rc5l16 ehci_hcd
[ 1.455786] usb usb1: SerialNumber: 0000:00:12.2
[ 1.458455] usb usb1: usb_probe_device
[ 1.458458] usb usb1: configuration #1 chosen from 1 choice
[ 1.458466] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 1.458508] hub 1-0:1.0: usb_probe_interface
[ 1.458510] hub 1-0:1.0: usb_probe_interface - got id
[ 1.458512] hub 1-0:1.0: USB hub found
[ 1.461078] hub 1-0:1.0: 6 ports detected
[ 1.463672] hub 1-0:1.0: standalone hub
[ 1.463674] hub 1-0:1.0: no power switching (usb 1.0)
[ 1.463675] hub 1-0:1.0: individual port over-current protection
[ 1.463677] hub 1-0:1.0: power on to power good time: 20ms
[ 1.463681] hub 1-0:1.0: local power source is good
[ 1.463683] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 1.463748] drivers/usb/core/inode.c: creating file '001'
[ 1.463831] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.466627] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 1.469394] drivers/usb/core/inode.c: creating file '002'
[ 1.469398] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 1.472291] ehci_hcd 0000:00:13.2: reset hcs_params 0x102306 dbg=1 cc=2 pcc=3 ordered !ppc ports=6
[ 1.472296] ehci_hcd 0000:00:13.2: reset hcc_params a072 thresh 7 uframes 256/512/1024
[ 1.472325] ehci_hcd 0000:00:13.2: debug port 1
[ 1.475259] ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.475268] ehci_hcd 0000:00:13.2: MWI active
[ 1.475270] ehci_hcd 0000:00:13.2: supports USB remote wakeup
[ 1.475286] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe7ff400
[ 1.478279] ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.478286] ehci_hcd 0000:00:13.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
[ 1.485057] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 1.488100] usb usb2: default language 0x0409
[ 1.488110] usb usb2: udev 1, busnum 2, minor = 128
[ 1.488112] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.491223] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.494401] usb usb2: Product: EHCI Host Controller
[ 1.497624] usb usb2: Manufacturer: Linux 2.6.34-rc5l16 ehci_hcd
[ 1.500842] usb usb2: SerialNumber: 0000:00:13.2
[ 1.504199] usb usb2: usb_probe_device
[ 1.504202] usb usb2: configuration #1 chosen from 1 choice
[ 1.504210] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 1.504254] hub 2-0:1.0: usb_probe_interface
[ 1.504256] hub 2-0:1.0: usb_probe_interface - got id
[ 1.504259] hub 2-0:1.0: USB hub found
[ 1.507437] hub 2-0:1.0: 6 ports detected
[ 1.510545] hub 2-0:1.0: standalone hub
[ 1.510546] hub 2-0:1.0: no power switching (usb 1.0)
[ 1.510548] hub 2-0:1.0: individual port over-current protection
[ 1.510550] hub 2-0:1.0: power on to power good time: 20ms
[ 1.510554] hub 2-0:1.0: local power source is good
[ 1.510556] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 1.510620] drivers/usb/core/inode.c: creating file '001'
[ 1.510757] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.513887] ohci_hcd: block sizes: ed 80 td 96
[ 1.513942] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.517138] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 1.520275] drivers/usb/core/inode.c: creating file '003'
[ 1.520282] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 3
[ 1.523528] ohci_hcd 0000:00:12.0: created debug files
[ 1.523530] ohci_hcd 0000:00:12.0: supports USB remote wakeup
[ 1.523545] ohci_hcd 0000:00:12.0: irq 16, io mem 0xfe7fe000
[ 1.563127] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000
[ 1.581104] ohci_hcd 0000:00:12.0: OHCI controller state
[ 1.581133] ohci_hcd 0000:00:12.0: OHCI 1.0, NO legacy support registers
[ 1.581137] ohci_hcd 0000:00:12.0: control 0x283 RWC HCFS=operational CBSR=3
[ 1.581141] ohci_hcd 0000:00:12.0: cmdstatus 0x00000 SOC=0
[ 1.581145] ohci_hcd 0000:00:12.0: intrstatus 0x00000004 SF
[ 1.581149] ohci_hcd 0000:00:12.0: intrenable 0x8000001a MIE UE RD WDH
[ 1.581159] ohci_hcd 0000:00:12.0: hcca frame #0005
[ 1.581163] ohci_hcd 0000:00:12.0: roothub.a 02001203 POTPGT=2 NOCP NPS NDP=3(3)
[ 1.581167] ohci_hcd 0000:00:12.0: roothub.b 00000000 PPCM=0000 DR=0000
[ 1.581170] ohci_hcd 0000:00:12.0: roothub.status 00008000 DRWE
[ 1.581175] ohci_hcd 0000:00:12.0: roothub.portstatus [0] 0x00000100 PPS
[ 1.581179] ohci_hcd 0000:00:12.0: roothub.portstatus [1] 0x00000100 PPS
[ 1.581182] ohci_hcd 0000:00:12.0: roothub.portstatus [2] 0x00000100 PPS
[ 1.581200] usb usb3: default language 0x0409
[ 1.581206] usb usb3: udev 1, busnum 3, minor = 256
[ 1.581208] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.584394] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.587541] usb usb3: Product: OHCI Host Controller
[ 1.590628] usb usb3: Manufacturer: Linux 2.6.34-rc5l16 ohci_hcd
[ 1.593792] usb usb3: SerialNumber: 0000:00:12.0
[ 1.597146] usb usb3: usb_probe_device
[ 1.597149] usb usb3: configuration #1 chosen from 1 choice
[ 1.597156] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 1.597199] hub 3-0:1.0: usb_probe_interface
[ 1.597201] hub 3-0:1.0: usb_probe_interface - got id
[ 1.597203] hub 3-0:1.0: USB hub found
[ 1.600451] hub 3-0:1.0: 3 ports detected
[ 1.603702] hub 3-0:1.0: standalone hub
[ 1.603704] hub 3-0:1.0: no power switching (usb 1.0)
[ 1.603705] hub 3-0:1.0: no over-current protection
[ 1.603707] hub 3-0:1.0: power on to power good time: 4ms
[ 1.603746] hub 3-0:1.0: local power source is good
[ 1.603748] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 1.603765] drivers/usb/core/inode.c: creating file '001'
[ 1.603795] ehci_hcd 0000:00:12.2: HS companion for 0000:00:12.0
[ 1.603821] ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.607277] ohci_hcd 0000:00:12.1: OHCI Host Controller
[ 1.610654] ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
[ 1.610657] hub 2-0:1.0: port 2: status 0501 change 0001
[ 1.610674] drivers/usb/core/inode.c: creating file '004'
[ 1.610677] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 4
[ 1.614143] ohci_hcd 0000:00:12.1: created debug files
[ 1.614145] ohci_hcd 0000:00:12.1: supports USB remote wakeup
[ 1.614152] ohci_hcd 0000:00:12.1: irq 16, io mem 0xfe7fd000
[ 1.672112] ohci_hcd 0000:00:12.1: OHCI controller state
[ 1.672126] ohci_hcd 0000:00:12.1: OHCI 1.0, NO legacy support registers
[ 1.672131] ohci_hcd 0000:00:12.1: control 0x283 RWC HCFS=operational CBSR=3
[ 1.672135] ohci_hcd 0000:00:12.1: cmdstatus 0x00000 SOC=0
[ 1.672138] ohci_hcd 0000:00:12.1: intrstatus 0x00000004 SF
[ 1.672142] ohci_hcd 0000:00:12.1: intrenable 0x8000001a MIE UE RD WDH
[ 1.672152] ohci_hcd 0000:00:12.1: hcca frame #0005
[ 1.672156] ohci_hcd 0000:00:12.1: roothub.a 02001203 POTPGT=2 NOCP NPS NDP=3(3)
[ 1.672160] ohci_hcd 0000:00:12.1: roothub.b 00000000 PPCM=0000 DR=0000
[ 1.672164] ohci_hcd 0000:00:12.1: roothub.status 00008000 DRWE
[ 1.672168] ohci_hcd 0000:00:12.1: roothub.portstatus [0] 0x00000100 PPS
[ 1.672172] ohci_hcd 0000:00:12.1: roothub.portstatus [1] 0x00000100 PPS
[ 1.672176] ohci_hcd 0000:00:12.1: roothub.portstatus [2] 0x00000100 PPS
[ 1.672194] usb usb4: default language 0x0409
[ 1.672200] usb usb4: udev 1, busnum 4, minor = 384
[ 1.672202] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.675686] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.679212] usb usb4: Product: OHCI Host Controller
[ 1.682783] usb usb4: Manufacturer: Linux 2.6.34-rc5l16 ohci_hcd
[ 1.686340] usb usb4: SerialNumber: 0000:00:12.1
[ 1.690019] usb usb4: usb_probe_device
[ 1.690022] usb usb4: configuration #1 chosen from 1 choice
[ 1.690029] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[ 1.690071] hub 4-0:1.0: usb_probe_interface
[ 1.690074] hub 4-0:1.0: usb_probe_interface - got id
[ 1.690076] hub 4-0:1.0: USB hub found
[ 1.693590] hub 4-0:1.0: 3 ports detected
[ 1.697033] hub 4-0:1.0: standalone hub
[ 1.697034] hub 4-0:1.0: no power switching (usb 1.0)
[ 1.697036] hub 4-0:1.0: no over-current protection
[ 1.697038] hub 4-0:1.0: power on to power good time: 4ms
[ 1.697076] hub 4-0:1.0: local power source is good
[ 1.697079] hub 4-0:1.0: trying to enable port power on non-switchable hub
[ 1.697096] drivers/usb/core/inode.c: creating file '001'
[ 1.697126] ehci_hcd 0000:00:12.2: HS companion for 0000:00:12.1
[ 1.697151] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.700732] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 1.704286] drivers/usb/core/inode.c: creating file '005'
[ 1.704290] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 1.704300] hub 3-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 1.707894] ohci_hcd 0000:00:13.0: created debug files
[ 1.707895] ohci_hcd 0000:00:13.0: supports USB remote wakeup
[ 1.707903] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe7fc000
[ 1.711552] hub 2-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 1.711566] hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 1.717108] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.720721] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.740466] ata2.00: ATAPI: TSSTcorp CDDVDW TS-L633C, AS01, max UDMA/100, ATAPI AN
[ 1.744031] ata2.00: applying bridge limits
[ 1.762130] ehci_hcd 0000:00:13.2: port 2 high speed
[ 1.762136] ehci_hcd 0000:00:13.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 1.766115] ohci_hcd 0000:00:13.0: OHCI controller state
[ 1.766121] ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
[ 1.766125] ohci_hcd 0000:00:13.0: control 0x283 RWC HCFS=operational CBSR=3
[ 1.766128] ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
[ 1.766132] ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
[ 1.766136] ohci_hcd 0000:00:13.0: intrenable 0x8000001a MIE UE RD WDH
[ 1.766146] ohci_hcd 0000:00:13.0: hcca frame #0005
[ 1.766150] ohci_hcd 0000:00:13.0: roothub.a 02001203 POTPGT=2 NOCP NPS NDP=3(3)
[ 1.766154] ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
[ 1.766158] ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
[ 1.766162] ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
[ 1.766166] ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00000100 PPS
[ 1.766170] ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
[ 1.766187] usb usb5: default language 0x0409
[ 1.766193] usb usb5: udev 1, busnum 5, minor = 512
[ 1.766195] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.769353] ata2.00: configured for UDMA/100
[ 1.771052] ata1.00: ATA-8: ST9320325AS, 0002SDM1, max UDMA/133
[ 1.771056] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.773195] ata1.00: configured for UDMA/133
[ 1.784208] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.784431] scsi 0:0:0:0: Direct-Access ATA ST9320325AS 0002 PQ: 0 ANSI: 5
[ 1.784771] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.784880] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 1.784915] sd 0:0:0:0: [sda] Write Protect is off
[ 1.784917] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.784932] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.806631] usb usb5: Product: OHCI Host Controller
[ 1.810424] usb usb5: Manufacturer: Linux 2.6.34-rc5l16 ohci_hcd
[ 1.814231] usb usb5: SerialNumber: 0000:00:13.0
[ 1.818060] usb 2-2: new high speed USB device using ehci_hcd and address 2
[ 1.818205] usb usb5: usb_probe_device
[ 1.818208] usb usb5: configuration #1 chosen from 1 choice
[ 1.818214] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[ 1.818261] hub 5-0:1.0: usb_probe_interface
[ 1.818263] hub 5-0:1.0: usb_probe_interface - got id
[ 1.818265] hub 5-0:1.0: USB hub found
[ 1.818305] hub 5-0:1.0: 3 ports detected
[ 1.818307] hub 5-0:1.0: standalone hub
[ 1.818308] hub 5-0:1.0: no power switching (usb 1.0)
[ 1.818310] hub 5-0:1.0: no over-current protection
[ 1.818311] hub 5-0:1.0: power on to power good time: 4ms
[ 1.818317] hub 5-0:1.0: local power source is good
[ 1.818319] hub 5-0:1.0: trying to enable port power on non-switchable hub
[ 1.818334] drivers/usb/core/inode.c: creating file '001'
[ 1.818370] ehci_hcd 0000:00:13.2: HS companion for 0000:00:13.0
[ 1.818413] Initializing USB Mass Storage driver...
[ 1.818460] usbcore: registered new interface driver usb-storage
[ 1.818462] USB Mass Storage support registered.
[ 1.818523] usbcore: registered new interface driver usbserial
[ 1.818546] USB Serial support registered for generic
[ 1.818690] sda:
[ 1.819984] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW TS-L633C AS01 PQ: 0 ANSI: 5
[ 1.827942] sda1 sda2 sda3 sda4 <sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.833881] Uniform CD-ROM driver Revision: 3.20
[ 1.834075] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.834159] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.838033] sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
[ 1.920327] ehci_hcd 0000:00:13.2: port 2 high speed
[ 1.920335] ehci_hcd 0000:00:13.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 1.920668] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.021853] usb 2-2: skipped 1 descriptor after configuration
[ 2.021857] usb 2-2: skipped 6 descriptors after interface
[ 2.021860] usb 2-2: skipped 1 descriptor after endpoint
[ 2.021862] usb 2-2: skipped 10 descriptors after interface
[ 2.022472] usb 2-2: default language 0x0409
[ 2.027723] usb 2-2: udev 2, busnum 2, minor = 129
[ 2.027726] usb 2-2: New USB device found, idVendor=04f2, idProduct=b071
[ 2.031785] usb 2-2: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[ 2.035896] usb 2-2: Product: CNF7129
[ 2.039907] usb 2-2: Manufacturer: Chicony Electronics Co., Ltd.
[ 2.043967] usb 2-2: SerialNumber: SN0001
[ 2.048137] usb 2-2: usb_probe_device
[ 2.048140] usb 2-2: configuration #1 chosen from 1 choice
[ 2.048596] usb 2-2: adding 2-2:1.0 (config #1, interface 0)
[ 2.051098] usb 2-2: adding 2-2:1.1 (config #1, interface 1)
[ 2.051186] drivers/usb/core/inode.c: creating file '002'
[ 2.051213] hub 4-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 2.051221] hub 5-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 2.051240] usbserial_generic 2-2:1.0: usb_probe_interface
[ 2.051245] usbserial_generic 2-2:1.0: usb_probe_interface - got id
[ 2.051255] usbserial_generic 2-2:1.1: usb_probe_interface
[ 2.051257] usbserial_generic 2-2:1.1: usb_probe_interface - got id
[ 2.051302] usbcore: registered new interface driver usbserial_generic
[ 2.055336] usbserial: USB Serial Driver core
[ 2.059501] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 2.066759] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 2.073271] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.077435] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.081553] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.085619] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.089653] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.093828] mice: PS/2 mouse device common for all mice
[ 2.098189] rtc_cmos 00:03: RTC can wake from S4
[ 2.102325] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 2.106310] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 2.110356] i2c /dev entries driver
[ 2.114427] i2c-core: driver [dev_driver] registered
[ 2.114479] i2c-dev: adapter [Radeon i2c bit bus VGA] registered as minor 0
[ 2.114526] i2c-dev: adapter [Radeon i2c bit bus LVDS] registered as minor 1
[ 2.114570] i2c-dev: adapter [Radeon i2c bit bus HDMI] registered as minor 2
[ 2.114866] Linux video capture interface: v2.00
[ 2.118962] uvcvideo 2-2:1.0: usb_probe_interface
[ 2.118969] uvcvideo 2-2:1.0: usb_probe_interface - got id
[ 2.118989] uvcvideo: Found UVC 1.00 device CNF7129 (04f2:b071)
[ 2.137397] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 2.145812] input: CNF7129 as /devices/pci0000:00/0000:00:13.2/usb2/2-2/2-2:1.0/input/input6
[ 2.149995] usbcore: registered new interface driver uvcvideo
[ 2.154055] USB Video Class driver (v0.1.0)
[ 2.158091] i2c-core: driver [ir-kbd-i2c] registered
[ 2.158093] Driver for 1-wire Dallas network protocol.
[ 2.162238] usbcore: registered new interface driver DS9490R
[ 2.166250] i2c-core: driver [ds2482] registered
[ 2.166256] 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
[ 2.170827] i2c-core: driver [bq27x00-battery] registered
[ 2.170857] i2c-core: driver [max17040] registered
[ 2.170971] i2c-core: driver [asb100] registered
[ 2.171111] IT87 WDT: no device
[ 2.175218] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[ 2.179609] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 2.183861] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 2.188122] usbcore: registered new interface driver btusb
[ 2.192323] cpuidle: using governor ladder
[ 2.196559] cpuidle: using governor menu
[ 2.201878] usbcore: registered new interface driver hiddev
[ 2.206149] usbcore: registered new interface driver usbhid
[ 2.210229] usbhid: USB HID core driver
[ 2.214340] asus_laptop: Asus Laptop Support version 0.42
[ 2.222696] asus_laptop: BSTS called, 0xff5f returned
[ 2.227318] asus_laptop: K51AE model detected
[ 2.254791] asus_laptop: Backlight controlled by ACPI video driver
[ 2.258792] input: Asus Laptop extra buttons as /devices/platform/asus_laptop/input/input7
[ 2.263378] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.281595] HDA Intel 0000:01:05.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.285863] HDA Intel 0000:01:05.1: setting latency timer to 64
[ 2.290174] ALSA device list:
[ 2.294074] #0: HDA ATI SB at 0xfe7f8000 irq 16
[ 2.297968] #1: HDA ATI HDMI at 0xfe9e8000 irq 19
[ 2.301856] IPv4 over IPv4 tunneling driver
[ 2.305799] GRE over IPv4 tunneling driver
[ 2.310696] TCP cubic registered
[ 2.314641] Initializing XFRM netlink socket
[ 2.318683] NET: Registered protocol family 10
[ 2.322569] lo: Disabled Privacy Extensions
[ 2.326343] tunl0: Disabled Privacy Extensions
[ 2.330101] NET: Registered protocol family 17
[ 2.333744] NET: Registered protocol family 15
[ 2.337305] Bluetooth: L2CAP ver 2.14
[ 2.340898] Bluetooth: L2CAP socket layer initialized
[ 2.344955] Bluetooth: RFCOMM TTY layer initialized
[ 2.348592] Bluetooth: RFCOMM socket layer initialized
[ 2.352314] Bluetooth: RFCOMM ver 1.11
[ 2.356043] lib80211: common routines for IEEE802.11 drivers
[ 2.359729] lib80211_crypt: registered algorithm 'NULL'
[ 2.359748] powernow-k8: Found 1 AMD Athlon(tm) II Dual-Core M300 processors (2 cpu cores) (version 2.20.00)
[ 2.363704] powernow-k8: 0 : pstate 0 (2000 MHz)
[ 2.367485] powernow-k8: 1 : pstate 1 (1400 MHz)
[ 2.371641] powernow-k8: 2 : pstate 2 (800 MHz)
[ 2.376496] rtc_cmos 00:03: setting system clock to 2010-04-21 07:33:38 UTC (1271835218)
[ 2.704113] ohci_hcd 0000:00:12.0: auto-stop root hub
[ 2.704135] ohci_hcd 0000:00:12.1: auto-stop root hub
[ 2.954112] ohci_hcd 0000:00:13.0: auto-stop root hub
[ 3.118529] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio4/input/input8
[ 3.204339] kjournald starting. Commit interval 5 seconds
[ 3.204399] EXT3-fs (sda5): mounted filesystem with writeback data mode
[ 3.204427] VFS: Mounted root (ext3 filesystem) readonly on device 8:5.
[ 3.224872] devtmpfs: mounted
[ 3.229387] Freeing unused kernel memory: 424k freed
[ 3.701132] hub 1-0:1.0: hub_suspend
[ 3.701148] usb usb1: bus auto-suspend
[ 3.701153] ehci_hcd 0000:00:12.2: suspend root hub
[ 4.701340] hub 3-0:1.0: hub_suspend
[ 4.701357] usb usb3: bus auto-suspend
[ 4.701383] ohci_hcd 0000:00:12.0: suspend root hub
[ 4.704145] hub 4-0:1.0: hub_suspend
[ 4.704160] usb usb4: bus auto-suspend
[ 4.704200] ohci_hcd 0000:00:12.1: suspend root hub
[ 4.704211] hub 5-0:1.0: hub_suspend
[ 4.704217] usb usb5: bus auto-suspend
[ 4.704222] ohci_hcd 0000:00:13.0: suspend root hub
[ 6.311570] udev: starting version 151
[ 6.355514] power_supply AC0: uevent
[ 6.355517] power_supply AC0: POWER_SUPPLY_NAME=AC0
[ 6.355522] power_supply AC0: Static prop TYPE=Mains
[ 6.355524] power_supply AC0: 1 dynamic props
[ 6.355527] power_supply AC0: prop ONLINE=1
[ 6.355566] power_supply BAT0: uevent
[ 6.355568] power_supply BAT0: POWER_SUPPLY_NAME=BAT0
[ 6.355571] power_supply BAT0: Static prop TYPE=Battery
[ 6.355573] power_supply BAT0: 14 dynamic props
[ 6.364747] power_supply BAT0: prop STATUS=Full
[ 6.364760] power_supply BAT0: prop PRESENT=1
[ 6.364768] power_supply BAT0: prop TECHNOLOGY=Li-ion
[ 6.364775] power_supply BAT0: prop CYCLE_COUNT=0
[ 6.364781] power_supply BAT0: prop VOLTAGE_MIN_DESIGN=11100000
[ 6.364788] power_supply BAT0: prop VOLTAGE_NOW=12450000
[ 6.364794] power_supply BAT0: prop CURRENT_NOW=0
[ 6.364800] power_supply BAT0: prop POWER_NOW=0
[ 6.364806] power_supply BAT0: prop ENERGY_FULL_DESIGN=48400000
[ 6.364812] power_supply BAT0: prop ENERGY_FULL=44858000
[ 6.364818] power_supply BAT0: prop ENERGY_NOW=44858000
[ 6.364824] power_supply BAT0: prop MODEL_NAME=F82--22
[ 6.364830] power_supply BAT0: prop MANUFACTURER=ASUSTEK
[ 6.364836] power_supply BAT0: prop SERIAL_NUMBER=
[ 7.218847] usb 2-2: link qh4-0001/ffff8800ce3f1b00 start 1 [1/0 us]
[ 7.218964] usb 2-2: unlink qh4-0001/ffff8800ce3f1b00 start 1 [1/0 us]
[ 11.019364] EXT3-fs (sda5): using internal journal
[ 11.232141] kjournald starting. Commit interval 5 seconds
[ 11.232712] EXT3-fs (sda7): using internal journal
[ 11.232726] EXT3-fs (sda7): mounted filesystem with writeback data mode
[ 13.699138] ATL1E 0000:02:00.0: irq 26 for MSI/MSI-X
[ 13.699337] ATL1E 0000:02:00.0: eth0: NIC Link is Up <100 Mbps Full Duplex>
[ 13.700684] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.702203] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 16.948129] power_supply AC0: uevent
[ 16.948133] power_supply AC0: POWER_SUPPLY_NAME=AC0
[ 16.948137] power_supply AC0: Static prop TYPE=Mains
[ 16.948140] power_supply AC0: 1 dynamic props
[ 16.948143] power_supply AC0: prop ONLINE=1
[ 16.948538] power_supply BAT0: uevent
[ 16.948540] power_supply BAT0: POWER_SUPPLY_NAME=BAT0
[ 16.948544] power_supply BAT0: Static prop TYPE=Battery
[ 16.948546] power_supply BAT0: 14 dynamic props
[ 16.957481] power_supply BAT0: prop STATUS=Full
[ 16.957487] power_supply BAT0: prop PRESENT=1
[ 16.957491] power_supply BAT0: prop TECHNOLOGY=Li-ion
[ 16.957493] power_supply BAT0: prop CYCLE_COUNT=0
[ 16.957496] power_supply BAT0: prop VOLTAGE_MIN_DESIGN=11100000
[ 16.957499] power_supply BAT0: prop VOLTAGE_NOW=12450000
[ 16.957501] power_supply BAT0: prop CURRENT_NOW=0
[ 16.957504] power_supply BAT0: prop POWER_NOW=0
[ 16.957506] power_supply BAT0: prop ENERGY_FULL_DESIGN=48400000
[ 16.957509] power_supply BAT0: prop ENERGY_FULL=44858000
[ 16.957511] power_supply BAT0: prop ENERGY_NOW=44858000
[ 16.957514] power_supply BAT0: prop MODEL_NAME=F82--22
[ 16.957516] power_supply BAT0: prop MANUFACTURER=ASUSTEK
[ 16.957518] power_supply BAT0: prop SERIAL_NUMBER=
[ 17.408410] ehci_hcd 0000:00:13.2: reused qh ffff8800ce3f1b00 schedule
[ 17.408421] usb 2-2: link qh4-0001/ffff8800ce3f1b00 start 1 [1/0 us]
[ 17.526323] usb 2-2: unlink qh4-0001/ffff8800ce3f1b00 start 1 [1/0 us]
[ 18.546836] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 18.557735] NFSD: starting 90-second grace period
[ 19.379163] cfg80211: Calling CRDA for country: DE
[ 20.540296] Adding 4000148k swap on /dev/mapper/swap. Priority:-1 extents:1 across:4000148k
[ 24.123302] eth0: no IPv6 routers present
[ 30.276633] alg: No test for lrw(twofish) (lrw(twofish-asm))
[ 30.314546] device-mapper: ioctl: unable to remove open device temporary-cryptsetup-2411
[ 31.767535] kjournald starting. Commit interval 5 seconds
[ 31.775825] EXT3-fs (dm-1): using internal journal
[ 31.775839] EXT3-fs (dm-1): mounted filesystem with writeback data mode
[/code2w7w8qdk]

then i plugged the device in, here is what got appended to dmesg
[code2w7w8qdk]
[ 54.897656] usb usb1: usb wakeup-resume
[ 54.897668] usb usb1: usb auto-resume
[ 54.897675] ehci_hcd 0000:00:12.2: resume root hub
[ 54.917121] hub 1-0:1.0: hub_resume
[ 54.917180] ehci_hcd 0000:00:12.2: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
[ 54.917192] hub 1-0:1.0: port 1: status 0501 change 0001
[ 55.018195] hub 1-0:1.0: state 7 ports 6 chg 0002 evt 0000
[ 55.018232] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[ 55.069138] ehci_hcd 0000:00:12.2: port 1 high speed
[ 55.069151] ehci_hcd 0000:00:12.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 55.120127] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 55.173144] ehci_hcd 0000:00:12.2: port 1 high speed
[ 55.173156] ehci_hcd 0000:00:12.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 55.247806] usb 1-1: default language 0x0409
[ 55.254436] usb 1-1: udev 2, busnum 1, minor = 1
[ 55.254443] usb 1-1: New USB device found, idVendor=148f, idProduct=3070
[ 55.254449] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 55.254455] usb 1-1: Product: 802.11 n WLAN
[ 55.254459] usb 1-1: Manufacturer: Ralink
[ 55.254463] usb 1-1: SerialNumber: 1.0
[ 55.254656] usb 1-1: usb_probe_device
[ 55.254665] usb 1-1: configuration #1 chosen from 1 choice
[ 55.254756] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 55.255989] usbserial_generic 1-1:1.0: usb_probe_interface
[ 55.255997] usbserial_generic 1-1:1.0: usb_probe_interface - got id
[ 55.256153] drivers/usb/core/inode.c: creating file '002'
[ 55.619214] rt2800usb 1-1:1.0: usb_probe_interface
[ 55.619225] rt2800usb 1-1:1.0: usb_probe_interface - got id
[ 55.634702] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 3070, rf: 0005, rev: 0201.
[ 55.639473] phy0: Selected rate control algorithm 'minstrel'
[ 55.639836] Registered led device: rt2800usb-phy0::radio
[ 55.639870] Registered led device: rt2800usb-phy0::assoc
[ 55.639900] Registered led device: rt2800usb-phy0::quality
[ 55.641777] usbcore: registered new interface driver rt2800usb
[ 55.705550] udev: renamed network interface wlan0 to wlan1
[/code2w7w8qdk]

some time after, i think when either bringing the interface up, or when scanning for APs, there are another few lines appended

[code2w7w8qdk]
[ 136.161742] phy0 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'.
[ 136.161754] rt2800usb 1-1:1.0: firmware: requesting rt2870.bin
[ 136.257619] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.22.
[ 136.422586] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
[ 136.424078] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
[ 136.425581] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
[ 136.427077] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
[ 136.430211] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[/code2w7w8qdk]