rt61,wpa_supplicant,centos 5.2/64bit

Live forum: http://rt2x00.serialmonkey.com/viewtopic.php?t=4923

radub

30-07-2008 14:53:26

Hi,

I have a Linksys WMP54G card. The chipset is RaLink RT2500/RT61.
I'm not able to setup the card under Centos 5.2 (64bit version).
Using an old post from here (viewtopic.php?t=4104) I was able to build the wpa_supplicant provided with the ralink drivers.
However when I try to start it I get the error attached below.
The version of the ralink driver and wpa_supplicant are
2008_0506_RT61_Linux_STA_v1.1.2.1
wpa_supplicant v0.5.8[/size1ckbnciq]The wpa_suplicant.conf is
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="linksys"
scan_ssid=1
key_mgmt=WPA-PSK
proto=WPA
pairwise=TKIP
group=TKIP
psk="secret password"[/size1ckbnciq]
Error log
[root@homepc network-scripts]# wpa_supplicant -d -Dralink -ira0 -c/etc/wpa_supplicant/wpa_supplicant.conf
Initializing interface 'ra0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'ralink' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
Priority group 0
id=0 ssid='linksys'
Initializing interface (2) 'ra0'
EAPOL SUPP_PAE entering state DISCONNECTED
EAPOL KEY_RX entering state NO_KEY_RECEIVE
EAPOL SUPP_BE entering state INITIALIZE
EAP EAP entering state DISABLED
EAPOL External notification - portEnabled=0
EAPOL External notification - portValid=0
wpa_driver_ralink_init
ralink_set_iface_flags
wpa_driver_ralink_flush_pmkid
ralink_set_oid oid=0x620 len (8) failed
ralink_set_oid oid=0x621 len (1) failed
RALINK Failed to set RT_OID_WPA_SUPPLICANT_SUPPORT(1)
wpa_driver_ralink_set_ssid
Own MAC address 001c106b0b56
wpa_driver_ralink_set_key
wpa_driver_ralink_get_bssid
ioctl[SIOCGIWAP] Transport endpoint is not connected
wpa_driver_ralink_remove_key
wpa_driver_ralink_set_key
wpa_driver_ralink_get_bssid
ioctl[SIOCGIWAP] Transport endpoint is not connected
wpa_driver_ralink_remove_key
wpa_driver_ralink_set_key
wpa_driver_ralink_get_bssid
ioctl[SIOCGIWAP] Transport endpoint is not connected
wpa_driver_ralink_remove_key
wpa_driver_ralink_set_key
wpa_driver_ralink_get_bssid
ioctl[SIOCGIWAP] Transport endpoint is not connected
wpa_driver_ralink_remove_key
Setting scan request 0 sec 100000 usec
Added interface ra0
State DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
wpa_driver_ralink_get_scan_results
Scan results 0
Selecting BSS from priority group 0
Try to find WPA-enabled AP
Try to find non-WPA AP
No suitable AP found.
Setting scan request 0 sec 0 usec
Starting AP scan (broadcast SSID)
wpa_driver_ralink_scan
wpa_driver_ralink_set_ssid
wpa_driver_ralink_scan_timeout
Scan timeout - try to get results
wpa_driver_ralink_get_scan_results
RALINK AP IEs - hexdump(len=20) 8b 01 79 90 09 01 00 00 64 00 11 04 dd 06 00 10 18 02 00 00
RALINK AP IEs - hexdump(len=38) c9 51 01 25 02 00 00 00 64 00 31 04 dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
Scan results 2
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0 001a92b0d568 ssid='Savage' wpa_ie_len=0 rsn_ie_len=0 caps=0x411
skip - no WPA/RSN IE
1 001c1027da72 ssid='linksys' wpa_ie_len=26 rsn_ie_len=0 caps=0x431
selected based on WPA IE
selected WPA AP 001c1027da72 ssid='linksys'
Try to find non-WPA AP
Trying to associate with 001c1027da72 (SSID='linksys' freq=2462 MHz)
Cancelling scan request
WPA clearing own WPA/RSN IE
Automatic auth_alg selection 0x1
WPA using IEEE 802.11i/D3.0
WPA Selected cipher suites group 8 pairwise 8 key_mgmt 2 proto 1
WPA set AP WPA IE - hexdump(len=26) dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
WPA clearing AP RSN IE
WPA using GTK TKIP
WPA using PTK TKIP
WPA using KEY_MGMT WPA-PSK
WPA Set own WPA IE default - hexdump(len=24) dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
State SCANNING -> ASSOCIATING
wpa_driver_ralink_associate
ralink_set_auth_mode
ralink_set_oid oid=0x617 len (1) failed
RALINK Failed to set OID_802_11_SET_IEEE8021X(0)
wpa_driver_ralink_set_ssid
Setting authentication timeout 10 sec 0 usec
EAPOL External notification - EAP success=0
EAPOL External notification - EAP fail=0
EAPOL External notification - portControl=Auto
wpa_driver_ralink_event_receive
h - hexdump(len=260) 04 01 00 00 10 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00 e1 00 0b 00 dd 00 02 8c 00 00 01 01 cd 00 41 80 ff ff ff ff 41 53 53 4f 43 49 4e 46 4f 28 52 65 71 49 45 73 3d 30 30 30 37 36 63 36 39 36 65 36 62 37 33 37 39 37 33 30 31 30 63 38 32 38 34 38 62 39 36 38 63 31 32 39 38 32 34 62 30 34 38 36 30 36 63 64 64 31 36 30 30 35 30 66 32 30 31 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 20 52 65 73 70 49 45 73 3d 30 31 30 63 38 32 38 34 38 62 39 36 38 63 31 32 39 38 32 34 62 30 34 38 36 30 36 63 64 64 31 38 30 30 35 30 66 32 30 31 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 30 30 30 30 29 00 00 00 00 00 00 00
wpa_driver_ralink_event_rtm_newlink
ifi - hexdump(len=16) 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00
attrlen=244
attr1 - hexdump(len=4) e1 00 0b 00
attr2 - hexdump(len=4) e1 00 0b 00
rta_type=0b
wpa_driver_ralink_event_wireless
Wireless event cmd=0x8c02 len=221
wpa_driver_ralink_event_wireless_custom
Custom wireless event 'ASSOCINFO(ReqIEs=00076c696e6b737973010c82848b968c129824b048606cdd160050f20101000050f20201000050f20201000050f202 RespIEs=010c82848b968c129824b048606cdd180050f20101000050f20201000050f20201000050f2020000)'
attr3 - hexdump(len=4) 00 00 00 00
wpa_driver_ralink_event_receive
h - hexdump(len=60) 3c 00 00 00 10 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00 1c 00 0b 00 18 00 15 8b 00 00 01 01 01 00 00 1c 10 27 da 72 00 00 00 00 00 00 00 00
wpa_driver_ralink_event_rtm_newlink
ifi - hexdump(len=16) 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00
attrlen=44
attr1 - hexdump(len=4) 1c 00 0b 00
attr2 - hexdump(len=4) 1c 00 0b 00
rta_type=0b
wpa_driver_ralink_event_wireless
Wireless event cmd=0x8b15 len=24
attr3 - hexdump(len=4) 4f 28 52 65
Authentication with 000000000000 timed out.
wpa_driver_ralink_get_bssid
ioctl[SIOCGIWAP] Transport endpoint is not connected
wpa_driver_ralink_poll_timeout Disconnected!!
Added BSSID 001c1027da72 into blacklist
No keys have been configured - skip key clearing
State SCANNING -> DISCONNECTED
EAPOL External notification - portEnabled=0
EAPOL External notification - portValid=0
EAPOL External notification - EAP success=0
Setting scan request 0 sec 0 usec
State DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
wpa_driver_ralink_scan
wpa_driver_ralink_set_ssid
wpa_driver_ralink_scan_timeout
Scan timeout - try to get results
wpa_driver_ralink_get_scan_results
RALINK AP IEs - hexdump(len=20) 89 81 4d 91 09 01 00 00 64 00 11 04 dd 06 00 10 18 02 00 00
RALINK AP IEs - hexdump(len=38) b6 61 d7 25 02 00 00 00 64 00 31 04 dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
Scan results 2
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0 001a92b0d568 ssid='Savage' wpa_ie_len=0 rsn_ie_len=0 caps=0x411
skip - no WPA/RSN IE
1 001c1027da72 ssid='linksys' wpa_ie_len=26 rsn_ie_len=0 caps=0x431
selected based on WPA IE
selected WPA AP 001c1027da72 ssid='linksys'
Try to find non-WPA AP
Trying to associate with 001c1027da72 (SSID='linksys' freq=2462 MHz)
Cancelling scan request
WPA clearing own WPA/RSN IE
Automatic auth_alg selection 0x1
WPA using IEEE 802.11i/D3.0
WPA Selected cipher suites group 8 pairwise 8 key_mgmt 2 proto 1
WPA set AP WPA IE - hexdump(len=26) dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
WPA clearing AP RSN IE
WPA using GTK TKIP
WPA using PTK TKIP
WPA using KEY_MGMT WPA-PSK
WPA Set own WPA IE default - hexdump(len=24) dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
State SCANNING -> ASSOCIATING
wpa_driver_ralink_associate
ralink_set_auth_mode
ralink_set_oid oid=0x617 len (1) failed
RALINK Failed to set OID_802_11_SET_IEEE8021X(0)
wpa_driver_ralink_set_ssid
Setting authentication timeout 10 sec 0 usec
EAPOL External notification - EAP success=0
EAPOL External notification - EAP fail=0
EAPOL External notification - portControl=Auto
wpa_driver_ralink_event_receive
h - hexdump(len=260) 04 01 00 00 10 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00 e1 00 0b 00 dd 00 02 8c 00 00 01 01 cd 00 41 80 ff ff ff ff 41 53 53 4f 43 49 4e 46 4f 28 52 65 71 49 45 73 3d 30 30 30 37 36 63 36 39 36 65 36 62 37 33 37 39 37 33 30 31 30 63 38 32 38 34 38 62 39 36 38 63 31 32 39 38 32 34 62 30 34 38 36 30 36 63 64 64 31 36 30 30 35 30 66 32 30 31 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 20 52 65 73 70 49 45 73 3d 30 31 30 63 38 32 38 34 38 62 39 36 38 63 31 32 39 38 32 34 62 30 34 38 36 30 36 63 64 64 31 38 30 30 35 30 66 32 30 31 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 30 30 30 30 29 00 00 00 00 00 00 00
wpa_driver_ralink_event_rtm_newlink
ifi - hexdump(len=16) 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00
attrlen=244
attr1 - hexdump(len=4) e1 00 0b 00
attr2 - hexdump(len=4) e1 00 0b 00
rta_type=0b
wpa_driver_ralink_event_wireless
Wireless event cmd=0x8c02 len=221
wpa_driver_ralink_event_wireless_custom
Custom wireless event 'ASSOCINFO(ReqIEs=00076c696e6b737973010c82848b968c129824b048606cdd160050f20101000050f20201000050f20201000050f202 RespIEs=010c82848b968c129824b048606cdd180050f20101000050f20201000050f20201000050f2020000)'
attr3 - hexdump(len=4) 00 00 00 00
wpa_driver_ralink_event_receive
h - hexdump(len=60) 3c 00 00 00 10 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00 1c 00 0b 00 18 00 15 8b 00 00 01 01 01 00 00 1c 10 27 da 72 00 00 00 00 00 00 00 00
wpa_driver_ralink_event_rtm_newlink
ifi - hexdump(len=16) 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00
attrlen=44
attr1 - hexdump(len=4) 1c 00 0b 00
attr2 - hexdump(len=4) 1c 00 0b 00
rta_type=0b
wpa_driver_ralink_event_wireless
Wireless event cmd=0x8b15 len=24
attr3 - hexdump(len=4) 4f 28 52 65
Authentication with 000000000000 timed out.
wpa_driver_ralink_get_bssid
ioctl[SIOCGIWAP] Transport endpoint is not connected
wpa_driver_ralink_poll_timeout Disconnected!!
BSSID 001c1027da72 blacklist count incremented to 2
No keys have been configured - skip key clearing
State SCANNING -> DISCONNECTED
EAPOL External notification - portEnabled=0
EAPOL External notification - portValid=0
EAPOL External notification - EAP success=0
Setting scan request 0 sec 0 usec
State DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
wpa_driver_ralink_scan
wpa_driver_ralink_set_ssid
wpa_driver_ralink_scan_timeout
Scan timeout - try to get results
wpa_driver_ralink_get_scan_results
RALINK AP IEs - hexdump(len=20) 88 91 23 92 09 01 00 00 64 00 11 04 dd 06 00 10 18 02 00 00
RALINK AP IEs - hexdump(len=38) 87 75 ad 26 02 00 00 00 64 00 31 04 dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
RALINK AP IEs - hexdump(len=20) 5e 72 c1 ae 16 00 00 00 64 00 11 04 dd 06 00 10 18 02 00 00
Scan results 3
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0 001a92b0d568 ssid='Savage' wpa_ie_len=0 rsn_ie_len=0 caps=0x411
skip - no WPA/RSN IE
1 001c1027da72 ssid='linksys' wpa_ie_len=26 rsn_ie_len=0 caps=0x431
skip - blacklisted
2 001b9e461ebd ssid='RTA1025W-461EBD' wpa_ie_len=0 rsn_ie_len=0 caps=0x411
skip - no WPA/RSN IE
Try to find non-WPA AP
0 001a92b0d568 ssid='Savage' wpa_ie_len=0 rsn_ie_len=0 caps=0x411
skip - SSID mismatch
1 001c1027da72 ssid='linksys' wpa_ie_len=26 rsn_ie_len=0 caps=0x431
skip - blacklisted
2 001b9e461ebd ssid='RTA1025W-461EBD' wpa_ie_len=0 rsn_ie_len=0 caps=0x411
skip - SSID mismatch
No APs found - clear blacklist and try again
Removed BSSID 001c1027da72 from blacklist (clear)
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0 001a92b0d568 ssid='Savage' wpa_ie_len=0 rsn_ie_len=0 caps=0x411
skip - no WPA/RSN IE
1 001c1027da72 ssid='linksys' wpa_ie_len=26 rsn_ie_len=0 caps=0x431
selected based on WPA IE
selected WPA AP 001c1027da72 ssid='linksys'
Try to find non-WPA AP
Trying to associate with 001c1027da72 (SSID='linksys' freq=2462 MHz)
Cancelling scan request
WPA clearing own WPA/RSN IE
Automatic auth_alg selection 0x1
WPA using IEEE 802.11i/D3.0
WPA Selected cipher suites group 8 pairwise 8 key_mgmt 2 proto 1
WPA set AP WPA IE - hexdump(len=26) dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
WPA clearing AP RSN IE
WPA using GTK TKIP
WPA using PTK TKIP
WPA using KEY_MGMT WPA-PSK
WPA Set own WPA IE default - hexdump(len=24) dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
State SCANNING -> ASSOCIATING
wpa_driver_ralink_associate
ralink_set_auth_mode
ralink_set_oid oid=0x617 len (1) failed
RALINK Failed to set OID_802_11_SET_IEEE8021X(0)
wpa_driver_ralink_set_ssid
Setting authentication timeout 10 sec 0 usec
EAPOL External notification - EAP success=0
EAPOL External notification - EAP fail=0
EAPOL External notification - portControl=Auto
wpa_driver_ralink_event_receive
h - hexdump(len=260) 04 01 00 00 10 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00 e1 00 0b 00 dd 00 02 8c 00 00 01 01 cd 00 41 80 ff ff ff ff 41 53 53 4f 43 49 4e 46 4f 28 52 65 71 49 45 73 3d 30 30 30 37 36 63 36 39 36 65 36 62 37 33 37 39 37 33 30 31 30 63 38 32 38 34 38 62 39 36 38 63 31 32 39 38 32 34 62 30 34 38 36 30 36 63 64 64 31 36 30 30 35 30 66 32 30 31 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 20 52 65 73 70 49 45 73 3d 30 31 30 63 38 32 38 34 38 62 39 36 38 63 31 32 39 38 32 34 62 30 34 38 36 30 36 63 64 64 31 38 30 30 35 30 66 32 30 31 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 30 31 30 30 30 30 35 30 66 32 30 32 30 30 30 30 29 00 00 00 00 00 00 00
wpa_driver_ralink_event_rtm_newlink
ifi - hexdump(len=16) 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00
attrlen=244
attr1 - hexdump(len=4) e1 00 0b 00
attr2 - hexdump(len=4) e1 00 0b 00
rta_type=0b
wpa_driver_ralink_event_wireless
Wireless event cmd=0x8c02 len=221
wpa_driver_ralink_event_wireless_custom
Custom wireless event 'ASSOCINFO(ReqIEs=00076c696e6b737973010c82848b968c129824b048606cdd160050f20101000050f20201000050f20201000050f202 RespIEs=010c82848b968c129824b048606cdd180050f20101000050f20201000050f20201000050f2020000)'
attr3 - hexdump(len=4) 00 00 00 00
wpa_driver_ralink_event_receive
h - hexdump(len=60) 3c 00 00 00 10 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00 1c 00 0b 00 18 00 15 8b 00 00 01 01 01 00 00 1c 10 27 da 72 00 00 00 00 00 00 00 00
wpa_driver_ralink_event_rtm_newlink
ifi - hexdump(len=16) 00 00 01 00 04 00 00 00 43 10 01 00 00 00 00 00
attrlen=44
attr1 - hexdump(len=4) 1c 00 0b 00
attr2 - hexdump(len=4) 1c 00 0b 00
rta_type=0b
wpa_driver_ralink_event_wireless
Wireless event cmd=0x8b15 len=24
attr3 - hexdump(len=4) 4f 28 52 65
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface ra0
State ASSOCIATING -> DISCONNECTED
No keys have been configured - skip key clearing
EAPOL External notification - portEnabled=0
EAPOL External notification - portValid=0
No keys have been configured - skip key clearing
Cancelling scan request
Cancelling authentication timeout
wpa_driver_ralink_deinit
ralink_set_oid oid=0x621 len (1) failed
RALINK Failed to set RT_OID_WPA_SUPPLICANT_SUPPORT(0)
wpa_driver_ralink_flush_pmkid
ralink_set_oid oid=0x620 len (8) failed
ralink_set_iface_flags[/size1ckbnciq]

Thank you.

Spy84464

30-07-2008 17:20:54

Hello,
we do not support Ralink's driver, please use our releases instead.

Regards,
Romain