rt2x00.serialmonkey.com

Support forum for the rt2x00 project
It is currently Wed Jun 19, 2013 11:41 pm

View unanswered posts | View active topics


Board index » rt2x00 Driver Support » rt2x00 Driver Support

All times are UTC




Post new topic Reply to topic  Page 1 of 1
  [ 7 posts ] 
  Print view Previous topic | Next topic 
Author Message
Rich43
PostPosted: Fri Sep 07, 2007 1:13 pm 
Offline

Joined: Thu Apr 26, 2007 8:20 pm
Posts: 14
Im running ubuntu and my D-Link DWL-G122 works out the box with no problems. It uses a rt73 chipset.

I **** you not, this thing has problems with windows.. its a nightmare to get working under windows.. even the official ralink drivers dont support it under windows and this driver has managed to get it working fine with linux and out the box!


Last edited by Rich43 on Sat Sep 08, 2007 12:55 am, edited 1 time in total.

Top
 Profile  
 
IvD
 Post subject:
PostPosted: Fri Sep 07, 2007 5:39 pm 
Offline
Site Admin

Joined: Sun Jun 05, 2005 1:01 pm
Posts: 5905
Location: Haarlem, The Netherlands
good to hear. :)

_________________
Regards,
Ivo van Doorn
Project Administrator
http://rt2x00.serialmonkey.com
Top
 Profile  
 
Rich43
 Post subject:
PostPosted: Sat Sep 08, 2007 12:51 am 
Offline

Joined: Thu Apr 26, 2007 8:20 pm
Posts: 14
Okay there are some problems after all..

Kernel is 2.6.22.. after a while of use the wireless cut out and I get this in dmesg, I cannot reconnect with any luck when it happens and pulling out the stick and putting back in just makes it worse.

[17076.187418] wlan1: Initial auth_alg=0
[17076.187423] wlan1: authenticate with AP 00:1b:2f:42:27:ee
[17076.188802] wlan1: RX authentication from 00:1b:2f:42:27:ee (alg=0 transaction=2 status=0)
[17076.188805] wlan1: authenticated
[17076.188807] wlan1: associate with AP 00:1b:2f:42:27:ee
[17076.192300] wlan1: RX AssocResp from 00:1b:2f:42:27:ee (capab=0x471 status=0 aid=1)
[17076.192304] wlan1: associated
[17076.192333] wlan1: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
[17076.192337] wlan1: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
[17076.192340] wlan1: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
[17076.192342] wlan1: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
[17076.194599] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[17076.204170] wlan1: RX WEP frame with unknown keyidx 2 (A1=33:33:00:00:00:16 A2=00:1b:2f:42:27:ee A3=00:19:5b:81:b1:58)
[17076.496125] wlan1: duplicate address detected!
[17079.743320] wlan1: duplicate address detected!
[18811.031638] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18811.131616] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x308c with error -110.
[18811.231597] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18811.331450] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18811.431428] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x308c with error -110.
[18812.531197] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18812.631176] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x308c with error -110.
[18812.731156] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18812.831134] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x30c4 with error -110.
[18812.931115] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18813.031093] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18813.131070] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18813.231050] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18813.331028] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x308c with error -110.
[18813.331132] phy0 -> rt73usb_bbp_write: Error - PHY_CSR3 register busy. Write failed.



.... some time later I got another error

[19527.929899] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3008 with error -110.
[19528.029877] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3024 with error -110.
[19528.129856] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3024 with error -110.
[19528.229834] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3020 with error -110.
[19528.329813] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3020 with error -110.
[19528.429792] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3040 with error -110.
[19528.529771] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3040 with error -110.
[19528.629625] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3050 with error -110.
[19528.729605] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3050 with error -110.
[19528.829584] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3064 with error -110.
[19528.929561] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3064 with error -110.
[19529.029540] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x01 failed for offset 0x0000 with error -110.
[19529.129520] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3030 with error -110.
[19529.229499] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3030 with error -110.
[19529.329477] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3030 with error -110.
[19529.445454] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3030 with error -110.
[19529.561429] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3030 with error -110.
[19529.677406] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3030 with error -110.
[19529.793382] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3030 with error -110.
[19529.809312] phy0 -> rt73usb_enable_radio: Error - Register initialization failed.
Top
 Profile  
 
mcmlxxii
 Post subject:
PostPosted: Sat Sep 08, 2007 7:51 am 
Offline

Joined: Sat Sep 08, 2007 7:28 am
Posts: 12
There are indeed some problems with the rt73usb module in Gutsy, it dies horribly (for me requiring a shut-down and restart), but it isn't the latest CVS. I couldn't get the CVS to compile, I think it requires a newer version of the wireless stack than the one in Gutsy. If you have any luck I'd be delighted to hear about it as I'd like to be help with testing!

On a more positive note, the rt73 module compiles and works flawlessly - see http://ubuntuforums.org/showthread.php?t=400236
Top
 Profile  
 
Austin_KW
 Post subject:
PostPosted: Tue Sep 11, 2007 1:16 pm 
Offline

Joined: Thu Jun 30, 2005 5:27 pm
Posts: 4
mcmlxxii wrote:
There are indeed some problems with the rt73usb module in Gutsy, it dies horribly (for me requiring a shut-down and restart), but it isn't the latest CVS. I couldn't get the CVS to compile, I think it requires a newer version of the wireless stack than the one in Gutsy. If you have any luck I'd be delighted to hear about it as I'd like to be help with testing!

On a more positive note, the rt73 module compiles and works flawlessly - see http://ubuntuforums.org/showthread.php?t=400236

If you look later in that thread http://ubuntuforums.org/showthread.php? ... ost3267508 you will see my instructions for compiling the cvs beta driver with gutsy.
Top
 Profile  
 
defcon
 Post subject: not anymore
PostPosted: Mon Oct 08, 2007 3:10 pm 
Offline

Joined: Sat Sep 22, 2007 10:00 am
Posts: 35
rt73 does not compile/run flawlessly anymore:
http://forum.deluge-torrent.org/viewtop ... 4e37f55547
Top
 Profile  
 
sefs
 Post subject:
PostPosted: Tue Oct 23, 2007 6:15 pm 
Offline

Joined: Sun Apr 22, 2007 12:51 pm
Posts: 27
Austin_KW does this solve the hard lock problem (scroll lock, caps lock blinking) with gutsy and rt73? That requires a hard reboot?

Thanks.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 7 posts ] 

Board index » rt2x00 Driver Support » rt2x00 Driver Support

All times are UTC


Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group